transient voltage suppressors smcj series speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electronic s circuit prote ct io n system
page:1 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smcj series features mechanical characteristics rating symbol value units peak pulse power dissipation at ta=25c by 10x1000s waveform (fig.1)(note 1), (note 2) p ppm 1500 watts power dissipation on in? nite heat sink at ta=50c p d 6.5 watts peak forward surge current, 8.3ms single half sine wave (note 3) i fsm 200 amps maximum instantaneous forward voltage at 25a for unidirectional only (note 4) v f 3.5v/5.0 v operating junction and storage temperature range. t j , t stg -55c to 150c c typical thermal resistance junction to lead r ujl 15 c/w typical thermal resistance junction to ambient r uja 75 c/w notes: 1. non-repetitive current pulse , per fig. 3 and derated above ta = 25c per fig. 2. 2. measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 perminute maximum. 3. vf<3.5v for devices of vbr < 200v and vf<5.0v for devices of vbr > 201v . 1. halogen-free 2. rohs compliant 3. typical maximum temperature coef ?cient 4. v br = 0.1% x v br @25c x t 5. glass passivated chip junction in do-214ab package 6. 1500w peak pulse capadility at 101000s waveform, repetition rate (duty cycles):0.01% 7. fast response time:typically less than 1.0ps from 0 volts to bv min 8. excellent clamping capability 9. low incremental surge resistance 10. typical ir less than 5a above 12v 11. high temperature soldering guaranteed: 260c/40 seconds / 0.375, 12. (9.5mm) lead length, 5lbs., (2.3kg) tension 13. plastic package has underwriters laboratory fammability classi?cation 94v-0 tvs devices are ideal for the protection of i/o interfaces,vcc bus and other vulnerable circuits used in telecom, computer , industrial and consumer electronic applications. uni bi uni bi anode cathode applications circuit prote ct io n system
transient voltage suppressors - smcj series page:2 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. electriacl characteristics type number device marking code reverse stand-off voltage breakdown voltage@i t test current maximum clamping voltage@i pp peak pulse current reverse leakage @v rwm (uni) (bi) uni bi v rwm (v) v br min. (v) v br max. (v) i t (ma) v c (v) i pp (a) i r (a) smcj5.0a smcj5.0ca gde bde 5.0 6.40 7.25 10 9.2 163.0 800 smcj6.0a smcj6.0ca gdg bdg 6.0 6.67 7.67 10 10.3 145.7 800 smcj6.5a smcj6.5ca gdk bdk 6.5 7.22 8.30 10 11.2 134.0 500 smcj7.0a smcj7.0ca gdm bdm 7.0 7.78 8.95 10 12.0 125.0 200 smcj7.5a smcj7.5ca gdp bdp 7.5 8.33 9.58 1 12.9 116.3 100 smcj8.0a smcj8.0ca gdr bdr 8.0 8.89 10.23 1 13.6 110.3 50 smcj8.5a smcj8.5ca gdt bdt 8.5 9.44 10.82 1 14.4 104.2 20 smcj9.0a smcj9.0ca gdv bdv 9.0 10.00 11.50 1 15.4 97.4 10 smcj10a smcj10ca gdx bdx 10.0 11.10 12.80 1 17.0 88.3 5 smcj11a smcj11ca gdz bdz 11.0 12.20 14.00 1 18.2 82.5 5 smcj12a smcj12ca gee bee 12.0 13.30 15.30 1 19.9 75.4 5 smcj13a smcj13ca geg beg 13.0 14.40 16.50 1 21.5 69.8 5 smcj14a smcj14ca gek bek 14.0 15.60 17.90 1 23.2 64.7 5 smcj15a smcj15ca gem bem 15.0 16.70 19.20 1 24.4 61.5 5 smcj16a smcj16ca gep bep 16.0 17.80 20.50 1 26.0 57.7 5 smcj17a smcj17ca ger ber 17.0 18.90 21.70 1 27.6 54.4 5 smcj18a smcj18ca get bet 18.0 20.00 23.30 1 29.2 51.4 5 smcj20a smcj20ca gev bev 20.0 22.20 25.50 1 32.4 46.3 5 smcj22a smcj22ca gex bex 22.0 24.40 28.00 1 35.5 42.3 5 smcj24a smcj24ca gez bez 24.0 26.70 30.70 1 38.9 38.6 5 smcj26a smcj26ca gfe bfe 26.0 28.90 33.20 1 42.1 35.7 5 smcj28a smcj28ca gfg bfg 28.0 31.10 35.80 1 45.4 33.1 5 smcj30a smcj30ca gfk bfk 30.0 33.30 38.30 1 48.4 31.0 5 smcj33a smcj33ca gfm bfm 33.0 36.70 42.20 1 53.3 28.2 5 smcj36a smcj36ca gfp bfp 36.0 40.00 46.00 1 58.1 25.9 5 smcj40a smcj40ca gfr bfr 40.0 44.40 51.10 1 64.5 23.3 5 smcj43a smcj43ca gft bft 43.0 47.80 54.90 1 69.4 21.7 5 smcj45a smcj45ca gfv bfv 45.0 50.00 57.50 1 72.7 20.6 5 smcj48a smcj48ca gjt bjt 48.0 53.30 61.30 1 77.4 19.4 5 smcj51a smcj51ca gjv bjv 51.0 56.70 65.20 1 82.4 18.2 5 smcj54a smcj54ca gfx bfx 54.0 60.00 69.00 1 87.1 17.3 5 smcj58a smcj58ca gfz bfz 58.0 64.40 74.10 1 93.6 16.1 5 smcj60a smcj60ca gge bge 60.0 66.70 76.70 1 96.8 15.5 5 smcj64a smcj64ca ggg bgg 64.0 71.10 81.80 1 103.0 14.6 5 smcj70a smcj70ca ggk bgk 70.0 77.80 89.50 1 113.0 13.3 5 smcj75a smcj75ca ggm bgm 75.0 83.30 95.80 1 121.0 12.4 5 smcj78a smcj78ca ggp bgp 78.0 86.70 99.70 1 126.0 11.9 5 smcj85a smcj85ca ggr bgr 85.0 94.40 108.20 1 137.0 11.0 5 smcj90a smcj90ca ggt bgt 90.0 100.00 115.50 1 146.0 10.3 5 smcj100a SMCJ100CA ggv bgv 100.0 111.00 128.00 1 162.0 9.3 5 smcj110a smcj110ca ggx bgx 110.0 122.00 140.50 1 177.0 8.5 5 smcj120a smcj120ca ggz bgz 120.0 133.00 153.00 1 193.0 7.8 5 smcj130a smcj130ca ghe bhk 130.0 144.00 165.50 1 209.0 7.2 5 smcj150a smcj150ca ghg bhg 150.0 167.00 192.60 1 243.0 6.2 5 smcj160a smcj160ca ghk bhk 160.0 178.00 197.00 1 259.0 5.8 5 smcj170a smcj170ca ghm bhm 170.0 189.00 209.00 1 275.0 5.5 5 smcj180a smcj180ca ghp bhp 180.0 198.00 222.00 1 292.0 5.1 5 smcj190a smcj190ca ghr bhr 190.0 209.00 243.20 1 308.0 4.8 5 smcj200a smcj200ca ghx bhx 200.0 220.00 247.00 1 324.0 4.6 5 smcj220a smcj220ca gje bje 220.0 242.00 272.00 1 356.0 4.2 5 smcj250a smcj250ca gjg bjg 250.0 279.00 309.00 1 405.0 3.7 5 smcj300a smcj300ca gjk bjk 300.0 335.00 371.00 1 486.0 3.1 5 circuit prote ct io n system
page:3 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smcj series ratings and characteristic curves figure 2 - pulse der ating cur ve figure 3 - pulse w av ef or m figure 4 - t ypical junction capacitanc e figure 5 - st eady stat e po we r der ating cur ve 5 figure 1 - p eak pulse p owe r ratin g figure 6 - maximum non-repetiti ve p eak fo rw ar d surg e curr ent uni-dir ectional onl y circuit prote ct io n system
transient voltage suppressors - smcj series page:4 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. soldering parameters fefow condition lead-free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(min) ) 200c - time (min to max) (t s ) 60-180 secs average ramp up rate (liquidus temp (t l ) to peak 3c/second max t s(max) to t l - ramp-up rate 3c/second max refow - temperature (t l ) (liquidus) 217c - time (min to max) (t s ) 60-150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20-40 seconds ramp-down rate 6c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c physical specifcations weight 0.007 ounce, 0.21 grams case jedec do214aa. molded plastic body over glass passivated junction polarity color band denotes cathode except bidirectional. termina matte tin-plated leads, solderable per jesd22-b102d environmental specifcations temperature cycle jesd22-a104 pressure cooker jesd 22-a102 high temp. storage jesd22-a103 htrb jesd22-a108 thermal shock jesd22-a106 circuit prote ct io n system
page:5 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. transient voltage suppressors - smcj series dimensions dim inches millimeters min max min max a 0.114 0.126 2.900 3.200 b 0.260 0.280 6.600 7.110 c 0.220 0.245 5.590 6.220 d 0.079 0.103 2.060 2.620 e 0.030 0.060 0.760 1.520 f - 0.008 0.203 g 0.305 0.320 7.750 8.130 h 0.006 0.012 0.152 0.305 0.129 3.300 0.094 24.00 k 0.165 4.200 l 0.094 2.400 unit:mm do-214ab (smc j-bend) part numbering system vo lt ag e bi-directional 5% v ol ta ge t olerance series xx xc a smcj packaging part number component package quantity packaging option packaging speci?cation smcjxxxxx do-214ab 500 tape & reel-16mm/13''tape eia std rs-481 circuit prote ct io n system
page:6 speci?cations are subject to change without notice. please refer to http://www.ruilon.com for current information. ruilongyuan electronics co., ltd. reproducing and modifying information of the document is prohibited without permission from ruilongyuan international inc. ruilongyuan international inc. reserves the rights to make changes of the content herein the document anytime without noti?cation. please refer to our website for the latest document. ruilongyuan international inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. ruilongyuan international inc. does not assume any and all implied warranties, including warranties of ?tness for particular purpose, non-infringement and merchantability. applications shown on the herein document are examples of standard use and operation. customers are responsible in comprehending the suitable use in particular applications.ruilongyuan international inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. the products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify ruilongyuan international inc. for any damages resulting from such improper use or sale. tel: +86-755-8290 8296 fax: +86-755-8290 8002 e-mail: jack@ruilon.com circuit prote ct io n system
|
